Recent content by shaunj187za

Got a pic of what you are trying to explain?

On the channel that is giving you frustration 1: Is the NVR set to "AI by Device" or "AI by Camera"? 2: Do your endpoints have G2 Acusense?

Thanks Again for the info. The Delay was defaintly there. but the good news is....... When the PTZ linkage was triggered the PTZ snapped in the correct direction and when the target move into the preset the smart track picked up the target and followed it out the scene. HOWEVER. I dont think...

So i am Assuming it was a "AMP" issue aka "Ampere" The 53V 60W unit has a 1.13 amp Rating. sent the unit into a boot loop The 55V 60W Generic has a 1.25 amp Rating=. This is the widely accepted generic (Brand: POE PLUS -) PSE65WI I have a AXIS PTZ 55v 60w POE which is Rated @1.35 amp I am...

@Kyle sorry for replying to such a old post. You have answered the foremost questions very well. But did not answer "Entrance/Region Exiting - " I bring this up because I am currently using this as a PTZ Linkage and it works. Where the line crossing does not work and I already have a task for...

@Phil @cymruchris I already have this unit in my inventory. Cudy 5 Port Gigabit 4 PoE 120W 1SFP Switch | GS1005PTS1 It has a 120w POE Budget, and by the flip of the switch it will make port #1 60WPOE (802.3bt) Is it worth a try? The Genuine Suplet POE's are like Hens teeth in my country...

I already have one of these coming in the mail. " Ubiquiti EdgePoint POE-54V-80W 54V 80W Gigabit Ethernet PoE Adapter" Do you think it will be adequate? Or should I send it back? BTW ^35USD half the price of the Suplet (Las60-57Cn-Rj45)

Sorry for the late reply. And i hope i didn't miss anything with regards to previous replies.... @paccmx. Can you confirm that you logged directly into the camera then Went to the PTZ tab then clicked on Smart Tracking and enabled smart tracking? Then go to smart events and make sure that the...

The client supplied the units, so it was his suppliers. The 53V and 56V POE Injectors are virtually identical. The printing on the plastic and the plastic moldings is identical. (probably made in the same factory) The sticker/label was the only way i could see that they was not identical. But...

So it seems this unit must have the 56v 60W POE injector to run at night. The unit was shipped with a 53v 60W POE injector and when night mode IR came on the device went into a kernal panic. Case closed

Good Day So i have come a long way from my primitive DS-2DF7284-A in 2014, With the Final Firmware being 2018. it is 2024 and have finally upgraded to the DS-2DF8225IX-AEL The Hikvision/Africa page has the firmware update (Firmware_V5.8.6_240124) While the .com only has the...

The PSU/Transformer is a 24V AC 3amp 72W The POE is a 60w 55v (1.25A-Max) Based on the above stat's in the PDF my power supply's should be sufficient. @Dan The issue started as we approached first night fall. now the unit is permanently in this mode.... I was able to source the "Latest...

@Dan is this PTZ in a boot loop? What is my options? I am able to active the device, I am.able to browse the web interface, but then 6 minutes later I loose communication with the device and then it does a reboot... Any input will be appreciated.

Hello Everyone, Trust you guys are well, and was hoping to get some feedback with a issue that I am having. I have installed x2 DS-2DF8225IH-AEL(W) this week. The one was powered by a 60W POE injector the other a 24V AC 3amp Power adapter( this was a upgrade from a 2DF7286-ael) As soon as...

Hello Everyone, I have acquired a iDS-7732NXI-I4/16P/X(B) 2020 I was very excited when I received this unit as it was my first deep-in-mind product. Currently I have a DS-7732NXI-I4. Its a 2023 model. Cosmetically, from the front, they look identical. So, I have tried to setup this unit as...