Search results

Hi @Roelli Due to the age of this camera, certain features like updating firmware will not work in the browser. To update firmware for older models like this, you will need to either use iVMS-4200(V3.12.1.5_E) or the Batch Configuration Tool I will say though, as far as I am aware, even when...

Hi @Sinbad We've never used Unifi cameras, so we don't know what their specs are when it comes to I-frames. If these cameras support you being able to adjust the I-frame settings, you would usually find these settings under the Video or Image settings. Unifi are relatively cheap...

Hi @Blink Can you please confirm the model number(s) of the 10 x 16 port NVRs you have?

Hi @bm_99 The spec you've highlighted above is explaining that the DVR can support HDTVI cameras at these different resolutions, but the higher the resolution of the camera you use, the lower the frame rate has to be. So if you connect 4MP HDTVI cameras to this DVR, you can have them...

You can find all of the firmware versions for the R0 cameras HERE Once you have updated through all of the versions in that folder, you can also update from V5.4.5 to this V5.4.800 Security Update Firmware

You can find the firmware for the NVR model discussed in this thread below: https://www.hikvisioneurope.com/eu/portal/?dir=portal/Technical%20Materials/13%20%20Z%20Phased%20out/01%20Back-ends/NVR/7100NI-SN

Hi @MarcF The only Hikvision models we are aware of that have both a varifocal lens and built-in audio are the newest Ultra Series G3 models (36x6G3/36x6GT Bullets & 37x6G3T Domes), but these are so new that there is little to no stock of these models available in the UK. Was there a specific...

Thanks @mattyp If you are considering a Tapo camera, I think you will need to use Passive PoE. I hadn't read the article closely enough before sending my first response and it wasn't clear from your original message if you were actually considering a Tapo camera or just using this as an...

Hi @mattyp Sorry, just need to check something. Can you please confirm the exact model number of the cameras you are trying to power?

Hi @mattyp Yes, it should be possible to connect a PoE Splitter to an active 802.3af PoE switch to power a non-PoE camera. All a PoE Splitter does is the reverse of a PoE Injector; it receives PoE and then separates it into power and data. The examples in that article show you 2 different...

Hi @safeqaz The camera options you are considering make sense and I don't think there are any other significantly different models we would recommend. In regards to NVR, if the system won't expand beyond 4 cameras, we would recommend the DS-7604NXI-K1/4P(D) 4-ch AcuSense NVR If you think you...

Hi @pat42 We are going to need more information than this. What brand are the CCTV boxes? What are the full model numbers of the CCTV boxes you have? Can you share photos of the "capital p and red xs" you describe?

Hi @rozi The newest firmware version to support RTMP would be this one - V5.7.1 But this firmware is for the core range of G2 cameras; the G2P panoramic cameras use slightly different firmware. If the 2387G2P camera won't accept the V5.7.1 firmware, that most likely means that the G2P models...

Thanks @Hikvsion If you look at the Hikvision product page for the DVR model you have, you'll see at the bottom of the page that there are 2 different firmware versions. The firmware you are currently running is for the (S) version of this DVR and there is a newer V4.75.020 firmware for the...

Hi @Hikvsion What firmware version is the DVR currently using? Where have you seen that the V4.75.020 and V4.50.110 firmware are the correct versions for your DVR?

Hi @MKSteve If you can't access the NVR with modern browsers like Chrome or Firefox, please try using Edge in IE mode

Hi @SCFudgell This is an old thread. Can you please create a new thread on the forum with more detail of exactly what your issue is? Please include the model numbers and firmware versions of the NVR and cameras you have. Also, if you have them, please share screenshots of what you are seeing...

Hi @MKSteve You can find the instructions for updating firmware HERE We would recommend that you first update to the last V3 firmware (V3.4.103), and you can then follow the same update order that I laid out in my original response.

Hi @bela Maybe try installing the ME firmware I believe this is for the Middle East region, but Hikvision often groups the Middle East with Africa (they usually refer to it as MEA - Middle East & Africa). If that firmware doesn't work, you will need to try and contact Hikvision Africa or a...

Hi @bela The firmware files are available on the DS-TCG405-E Product Page from the Hikvision Global site.