Search results

I would have liked the HIK135 version because it has a smaller profile. Looks like I'll have to order the larger TRL one instead. Thanks for your reply.

Hi, Will the Hikvision DS-2CD2383G0-I fit on the HIK135 DS-1273ZJ-130 wall mount bracket? Thanks

Thank you Dan for letting me know.

Ok Dan. Please let me know if you can when they put it right.

I loaned my digital camera to someone so I can't take any photos at the moment. I updated the firmware to the one in your link and finally managed to get the cameras on 1 page. I have another problem now. In the event menu I no longer have the line crossing or the intrusion. There is no smart...

Hi Dan, Just tried that and it didn't work unfortunately. 1+7 shows 4 pages 1+5 6 pages 1 32 pages 2 32 pages 4 8 pages 3+3 4 pages This is a strange one. What do you sugest next? Thanks

Thanks

I now have 6 cameras connected directly to my NVR DS-7608NI-I2/8P to test and have 1+7 split problem. My firmware is V4.40.017. I updated to the latest version V4.50.000 and when I went to setup the split screen to 1+7 I ended up with 3 pages and not 1. I back dated the firmware back to...

I'm totally new to connecting cameras in this way. So no harm will come to the NVR outputting 48V into the PoE switch that is also outputting 48 Volts. Is this correct? Can you recommend a cheap PoE switch that will work. Thanks

All sorted now. Thank you

I have a Hikvision DS-7608NI-I2/8P. I have 3 cameras connected to it and it's a 8 port. It is refusing to allow me to connect any more cameras. It comes up with no more ip cameras allowed when I try and connect them through the LAN. When I try and connect more cameras direct the the NVR it...

1 camera but I need to connect 2 through 1 cable. I was thinking if I can cut power from the port at the nvr end then all I need is a 12V PSU at the other end to power both cameras.

Does anyone know what wires/pin numbers to cut to stop the PoE from the NVR? If I can cut the 48V wires in that 1 cable then my job will be a lot easier and I already have the stuff here.

I tried to turn off the PoE power on the port and it still was putting power out on the port from the NVR. I could have used a normal switch then and powered the 2 camera from a 12V supply. That would of been the best solution as I already have a normal Gigabit switch here. Q. 1. If I put a PoE...

Q.1 Do I need to switch off the PoE on that 1 port on the NVR? Q.2 Is the NVR capable of seeing both cameras from the 1 port? Q3. So I need to put the PoE switch at the 2 camera end of the Cat6?

I have a DS-7608NI-I2-8P. I only have 1 cable at the top of the garden and I need to install a second 4K camera from the same cable. Both cameras do not have sound built in. Is this possible? Thanks

Thank you for explaining. It all makes sense now.

I have a Hikvision NVR that outputs 48 volts through POE. When I first setup the camera I used a 12v PSU to power the camera to initially setup the camera in my living room. It’s an ANKKE 8mp camera and I need to connect the camera back through my router and not the NVR. I don't want to run a...

Just installed a new 3tb SkyHawk HDD ST3000VX009 into my DS-7608NI-L2/8P NVR. Firmware V4.1.63 buld 190111. Formatted the drive OK and everything is runnining. The problem I have is when I go to HDD in health I get 0 HDD detected. The detection is only available for SkyHawk seagate HDD but...