Search results

Hello johnfitzy. Thank you for your reply. If you're on version 5 would you be able to tell me if you have had problems with scrubbing, because if not then my solution would be to upgrade to version 5. Could you also tell me how many channels / cameras you have and spec of cameras so that...

Okay. Perhaps this https://www.use-ip.co.uk/forum/threads/scrolling-scrubbing-through-playback-timeline.12522/ was a little too long hence no replies. So how about this: Does anybody with an M Series NVR have any issues with scrolling (scrubbing) playback through the timeline.

Irrespective of what HIK say, you are the legal owner as you bought the house and its belongings. Getting HIK to recognise this may be another issue.

Me again folks. Thank in advance to anyone who reads this as it might seem a lengthy explanation. The issue I am about to explain is my main concern with m 7608m2 8p setup. I upgraded from the K2 8p because I wanted to replace some of my G0 4mp cameras with 8mp, because I had to throttle...

The h does stand for hybrid.

Thank you very much again.. I need to learn to scroll the page if not all of it fits on the window. DOH

Thank you JB. I do now have motion sorted. I hadn't realised these were now being shown as event in red as opposed to motion in green so they were there all the time on the smart button. The other thing that complicated matters was how Hik had changed the way views are accessed. If you...

Struggling to find the enable virtual host setting on the nvr gui V 4.0 software via web browser. I have accessed configuration/ system / channel management tab where this lists each camera its IP settings etc and at the right hand side of the page each camera has an edit tab in the operation...

Good Morning. JB. When you have motion enabled what shows in the timeline in "normal" view. What colour. With the V3 software it was green markers spanning the duration of the movement. I don't have these in v4 I only have a continuous record blue line. I want continuous record. In v4...

Thank you again I'll give that one a go.

Spot on found it. Thank you very much JB. Does lead to another question though. On playback with version 3 I could see green motion detection lines on the timeline. Can't see any of these now on any cameras. Whether this be normal view or smart view. I have confirmed that motion...

Hello Chaps Finally replaced my 7608k28p with the equivalent M series. Swapped cameras fine, no issues. Thanks JB for your advice about 12 months ago. (Takes me a long time to get round to stuff). The only question I have. I can't seem to find the motion detection settings for each...

The minimum low light specification for the hybrid camera is way better than the direct replacement. The Hybrid camera uses it's inbuilt light to illuminate a scene. It's a pretty powerful light. It's also has a larger lens aperture and larger sensor than the other camera. All pointing to...

No product in that link

Ok JB. Very much appreciate the advice and explaining the pitfalls I may encounter.

Thanks for your advice once more JB. I will need to change the password on 2 cams first as they dont match the NVR's password but also I will be changing cam settings after the upgrade as they are throttled back at the moment due to the K NVR struggling with decoding. Therefore can I use...

I decided to upgrade to an 8 channel M series.. I currently have a 7608 K2 using the latest version 3 software (not v4) with 7 cams of G0, G1 and G2(c) variants connected to POE ports on the NVR. My question is. What is the correct procedure to transfer these cams to the M series NVR...

Hi Did you get this. How much does it knock down the noise.

I have still got my 7608 K2 on v3 firmware but am thinking it's about time to get v4. Also to look at upgrading a couple of cams so it's gonna be an M series NVR for me rather than just a firm upgrade on the K. I may opt for the 16 channel as opposed to the 8 but my main concern is fan noise...