Hi
All Cameras settings are set by camera except one that is only included in NVR settings.
This setting is Linkage Action-Audio Alarm. I do this first, selecting only the type of Smart Event I want to use. But you can do on all kind of Events for future use. This remains selected when saved once.
- All my Image->Display settings are left to default except the Day/night switch which I select different setting. Exposure Time = 1/12, LC WDR HLC are OFF
- Try reducing Threshold(Seuil) to 0. Setting at 2 gives two more seconds for someone loitering inside the area. Adding this to processing time gives a result of more than 5 seconds of delay and surely not an event alarm.
- I usually do settings on cameras from IVMS and I also do settings on Edge(Ie Mode). I do not do Event settings from NVR
- If you see that some of the settings are not visible on NVR GUI, you can apply them on the NVR but then you have to do them again on IVMS or Edge Camera settings
- Reboot the NXI NVR after doing all settings is always necessary.
- I told you about the size of the target because I compared with the size of the person and the size of the car.
- The Configuration - Live View - Alarm Pop-up delay is not under SMD or Smart Event settings. You can find it only on NVR GUI->Configuration - Live View - Alarm Pop-up delay
Now about the rectangles and decagons I can not understand why they fixed only for VCA mode by NVR and not VCA mode by Camera.
This is what they write on K20A9_V4.75.005build230630_ReleaseNotes.pdf:
"7. Perimeter algorithm optimization
. Supports a max of 10 points
Support max and min rule"
They don't write only for VCA mode By NVR
There is a similar issue on IVMS where when searching for VCA events, you can only draw a triagle??????
And the problem with the plug-ins they will never solve, either for GUIs or for IVMS and browsers. Think of that they are still counting on Internet Explorer for IVMS
This is silly
All Cameras settings are set by camera except one that is only included in NVR settings.
This setting is Linkage Action-Audio Alarm. I do this first, selecting only the type of Smart Event I want to use. But you can do on all kind of Events for future use. This remains selected when saved once.
- All my Image->Display settings are left to default except the Day/night switch which I select different setting. Exposure Time = 1/12, LC WDR HLC are OFF
- Try reducing Threshold(Seuil) to 0. Setting at 2 gives two more seconds for someone loitering inside the area. Adding this to processing time gives a result of more than 5 seconds of delay and surely not an event alarm.
- I usually do settings on cameras from IVMS and I also do settings on Edge(Ie Mode). I do not do Event settings from NVR
- If you see that some of the settings are not visible on NVR GUI, you can apply them on the NVR but then you have to do them again on IVMS or Edge Camera settings
- Reboot the NXI NVR after doing all settings is always necessary.
- I told you about the size of the target because I compared with the size of the person and the size of the car.
- The Configuration - Live View - Alarm Pop-up delay is not under SMD or Smart Event settings. You can find it only on NVR GUI->Configuration - Live View - Alarm Pop-up delay
Now about the rectangles and decagons I can not understand why they fixed only for VCA mode by NVR and not VCA mode by Camera.
This is what they write on K20A9_V4.75.005build230630_ReleaseNotes.pdf:
"7. Perimeter algorithm optimization
. Supports a max of 10 points
Support max and min rule"
They don't write only for VCA mode By NVR
There is a similar issue on IVMS where when searching for VCA events, you can only draw a triagle??????
And the problem with the plug-ins they will never solve, either for GUIs or for IVMS and browsers. Think of that they are still counting on Internet Explorer for IVMS
This is silly